Chinese translation for "cutter teeth"
|
- 牙轮齿
Related Translations:
- Example Sentences:
| 1. | Based on the cutting experiments used by cutter tooth and point - attack pick on the press and cutting simulation test table , the deformation and failure process of coal body are studied by the method of white light digital speckle correlation
摘要采用白光数字散斑相关测定方法，在压力机上，在截割模拟实验台上分别对煤试件进行刀齿、镐齿的截割实验，研究被截割煤体的变形破坏过程。 | | 2. | Abstract cutter teeth and gear teeth are simplified as mechanical models , the bending deformation at contact nodes is calculated by applying the three - dimension finite element method and analyzing their mechanical condition , the relation curve between shaving force and bending deformation is drawn out
简介：摘要将刀齿和轮齿抽象简化为力学模型，分析其受力状态，并运用三维有限单元法计算各节点的弯曲变形量。 | | 3. | The results indicate that a stable deformation localization band occurs in the coal cutting course and develops to macroscopic crack ; the deformation localization band is slantwise ; while the cutter tooth is used , the deformation localization develops slowly , and the localization becomes wider and the strain value in the band area higher afterwards ; when the point - attack pick used the localization develops quickly and the localization band becomes narrow and the strain value in the band lower
研究表明：截齿截割煤体过程中，煤体出现稳定的变形局部化带，且最终发展为宏观裂纹；煤体变形局部化带为一个倾斜带：刀齿截割时，变形局部化发展较慢，但产生变形局部化后，局部化带宽且带内应变值较高；而镐齿截割时，变形局部化发展较快，但产生局部化后，局部化带窄且带内应变值不如刀齿高。 | | 4. | For cutting the composite lock gear with unequal tooth thickness , a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile . the cutter tooth arrangement , the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented . and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters . to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据.结果表明，采用上述方法设计非标准复合齿轮插齿刀，可简化计算和提高设计效率 |
- Similar Words：
- "cutter suctic dredge" Chinese translation, "cutter suction dredge" Chinese translation, "cutter suction dredger" Chinese translation, "cutter switch" Chinese translation, "cutter technic" Chinese translation, "cutter thrower" Chinese translation, "cutter tilt" Chinese translation, "cutter tool holder" Chinese translation, "cutter tooth number" Chinese translation, "cutter tooth top" Chinese translation
|
|
|
